Beta: metal milling. Every number is copied as published by the tool maker and linked to its source. A machinist hasn't reviewed this section yet; rows marked ⚠ have a specific open question. Starting points only: verify against your tool's own chart.
Titanium: SFM & IPT for carbide end mills
404 published values. RPM = 3.82 × SFM ÷ D, feed IPM = RPM × flutes × IPT. Calculate for your machine →
Harvey Tool: General Machining Guidelines: Carbide End Mills
Tool: Solid carbide end mill (general guideline, any flute count). Facts copied with attribution and link; table layout not reproduced. Harvey notes values are suggested starting values.
| Grade (as listed) | Cut | Dia | SFM | IPT (in) | Review | Source |
|---|---|---|---|---|---|---|
| Commercially Pure, 6AL-4V, ASTM 1/2/3, 6AL-25N-4Zr-2Mo-Si (as printed by Harvey) | general | 1/8" | 50–250 | 0.0005 | ⚠ SFM range 50-250 spans CP and 6Al-4V; 6Al-4V usually needs the low end. Confirm. Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Harvey Tool |
| Commercially Pure, 6AL-4V, ASTM 1/2/3, 6AL-25N-4Zr-2Mo-Si (as printed by Harvey) | general | 3/16" | 50–250 | 0.0005 | ⚠ SFM range 50-250 spans CP and 6Al-4V; 6Al-4V usually needs the low end. Confirm. Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Harvey Tool |
| Commercially Pure, 6AL-4V, ASTM 1/2/3, 6AL-25N-4Zr-2Mo-Si (as printed by Harvey) | general | 1/4" | 50–250 | 0.0005 | ⚠ SFM range 50-250 spans CP and 6Al-4V; 6Al-4V usually needs the low end. Confirm. Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Harvey Tool |
| Commercially Pure, 6AL-4V, ASTM 1/2/3, 6AL-25N-4Zr-2Mo-Si (as printed by Harvey) | general | 3/8" | 50–250 | 0.001 | ⚠ SFM range 50-250 spans CP and 6Al-4V; 6Al-4V usually needs the low end. Confirm. Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Harvey Tool |
| Commercially Pure, 6AL-4V, ASTM 1/2/3, 6AL-25N-4Zr-2Mo-Si (as printed by Harvey) | general | 1/2" | 50–250 | 0.001 | ⚠ SFM range 50-250 spans CP and 6Al-4V; 6Al-4V usually needs the low end. Confirm. Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Harvey Tool |
| Commercially Pure, 6AL-4V, ASTM 1/2/3, 6AL-25N-4Zr-2Mo-Si (as printed by Harvey) | general | 5/8" | 50–250 | 0.0015 | ⚠ SFM range 50-250 spans CP and 6Al-4V; 6Al-4V usually needs the low end. Confirm. Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Harvey Tool |
| Commercially Pure, 6AL-4V, ASTM 1/2/3, 6AL-25N-4Zr-2Mo-Si (as printed by Harvey) | general | 3/4" | 50–250 | 0.002 | ⚠ SFM range 50-250 spans CP and 6Al-4V; 6Al-4V usually needs the low end. Confirm. Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Harvey Tool |
| Commercially Pure, 6AL-4V, ASTM 1/2/3, 6AL-25N-4Zr-2Mo-Si (as printed by Harvey) | general | 1" | 50–250 | 0.004 | ⚠ SFM range 50-250 spans CP and 6Al-4V; 6Al-4V usually needs the low end. Confirm. Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Harvey Tool |
| 5AL-2.5Sn-ELI, 8Al-1Mo-1V | general | 1/8" | 90–120 | 0.0005 | – ✓ Cross-checked | Harvey Tool |
| 5AL-2.5Sn-ELI, 8Al-1Mo-1V | general | 3/16" | 90–120 | 0.0005 | – ✓ Cross-checked | Harvey Tool |
| 5AL-2.5Sn-ELI, 8Al-1Mo-1V | general | 1/4" | 90–120 | 0.0005 | – ✓ Cross-checked | Harvey Tool |
| 5AL-2.5Sn-ELI, 8Al-1Mo-1V | general | 3/8" | 90–120 | 0.001 | – ✓ Cross-checked | Harvey Tool |
| 5AL-2.5Sn-ELI, 8Al-1Mo-1V | general | 1/2" | 90–120 | 0.001 | – ✓ Cross-checked | Harvey Tool |
| 5AL-2.5Sn-ELI, 8Al-1Mo-1V | general | 5/8" | 90–120 | 0.0015 | – ✓ Cross-checked | Harvey Tool |
| 5AL-2.5Sn-ELI, 8Al-1Mo-1V | general | 3/4" | 90–120 | 0.002 | – ✓ Cross-checked | Harvey Tool |
| 5AL-2.5Sn-ELI, 8Al-1Mo-1V | general | 1" | 90–120 | 0.004 | – ✓ Cross-checked | Harvey Tool |
Helical Solutions (Harvey Performance): Speeds & Feeds HSV-4 / HSV-RN-4 / HSM-4 (4 flute, variable pitch)
Tool: 4-flute variable-pitch carbide end mill (HSV-4). Facts copied with attribution and link; PDF not re-hosted. IPT is for 2.5xD LOC, non-reached tools.
| Grade (as listed) | Cut | Dia | SFM | IPT (in) | Review | Source |
|---|---|---|---|---|---|---|
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | slotting | 1/16" | 300 | 0.0004 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | roughing | 1/16" | 300 | 0.0008 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | finishing | 1/16" | 300 | 0.0009 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | slotting | 3/32" | 300 | 0.0006 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | roughing | 3/32" | 300 | 0.0011 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | finishing | 3/32" | 300 | 0.0014 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | slotting | 1/8" | 300 | 0.0008 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | roughing | 1/8" | 300 | 0.0015 | – ⚠ Outlier (for review): IPT 0.0015 vs median 0.0005 of 4 other source(s) (+200%); SFM 300 vs median 162.5 of 6 other source(s) (+85%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | finishing | 1/8" | 300 | 0.0018 | – ⚠ Outlier (for review): IPT 0.0018 vs median 0.0005 of 4 other source(s) (+260%); SFM 300 vs median 162.5 of 6 other source(s) (+85%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | slotting | 3/16" | 300 | 0.0013 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | roughing | 3/16" | 300 | 0.0022 | – ⚠ Outlier (for review): IPT 0.0022 vs median 0.00075 of 3 other source(s) (+193%); SFM 300 vs median 162.5 of 6 other source(s) (+85%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | finishing | 3/16" | 300 | 0.002 | – ⚠ Outlier (for review): IPT 0.002 vs median 0.00075 of 3 other source(s) (+167%); SFM 300 vs median 162.5 of 6 other source(s) (+85%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | slotting | 1/4" | 300 | 0.0017 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | roughing | 1/4" | 300 | 0.0029 | – ⚠ Outlier (for review): IPT 0.0029 vs median 0.0009 of 6 other source(s) (+222%); SFM 300 vs median 162.5 of 6 other source(s) (+85%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | finishing | 1/4" | 300 | 0.0023 | – ⚠ Outlier (for review): IPT 0.0023 vs median 0.0009 of 6 other source(s) (+156%); SFM 300 vs median 162.5 of 6 other source(s) (+85%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | slotting | 3/8" | 300 | 0.0025 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | roughing | 3/8" | 300 | 0.0043 | – ⚠ Outlier (for review): IPT 0.0043 vs median 0.00135 of 6 other source(s) (+219%); SFM 300 vs median 162.5 of 6 other source(s) (+85%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | finishing | 3/8" | 300 | 0.0027 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | slotting | 1/2" | 300 | 0.0032 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | roughing | 1/2" | 300 | 0.0057 | – ⚠ Outlier (for review): IPT 0.0057 vs median 0.001575 of 6 other source(s) (+262%); SFM 300 vs median 162.5 of 6 other source(s) (+85%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | finishing | 1/2" | 300 | 0.0031 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | slotting | 3/4" | 300 | 0.0046 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | roughing | 3/4" | 300 | 0.0081 | – ⚠ Outlier (for review): IPT 0.0081 vs median 0.002437 of 6 other source(s) (+232%); SFM 300 vs median 162.5 of 6 other source(s) (+85%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | finishing | 3/4" | 300 | 0.0037 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | slotting | 1" | 300 | 0.0059 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | roughing | 1" | 300 | 0.0103 | – ⚠ Outlier (for review): IPT 0.0103 vs median 0.003687 of 6 other source(s) (+179%); SFM 300 vs median 162.5 of 6 other source(s) (+85%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (< 75 HRB) | finishing | 1" | 300 | 0.0045 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | slotting | 1/16" | 275 | 0.0004 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | roughing | 1/16" | 275 | 0.0006 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | finishing | 1/16" | 275 | 0.0009 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | slotting | 3/32" | 275 | 0.0005 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | roughing | 3/32" | 275 | 0.0009 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | finishing | 3/32" | 275 | 0.0013 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | slotting | 1/8" | 275 | 0.0007 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | roughing | 1/8" | 275 | 0.0012 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | finishing | 1/8" | 275 | 0.0017 | – ⚠ Outlier (for review): IPT 0.0017 vs median 0.0005 of 4 other source(s) (+240%); SFM 275 vs median 162.5 of 6 other source(s) (+69%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | slotting | 3/16" | 275 | 0.001 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | roughing | 3/16" | 275 | 0.0018 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | finishing | 3/16" | 275 | 0.0019 | – ⚠ Outlier (for review): IPT 0.0019 vs median 0.00075 of 3 other source(s) (+153%); SFM 275 vs median 162.5 of 6 other source(s) (+69%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | slotting | 1/4" | 275 | 0.0014 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | roughing | 1/4" | 275 | 0.0024 | – ⚠ Outlier (for review): IPT 0.0024 vs median 0.0009 of 6 other source(s) (+167%); SFM 275 vs median 162.5 of 6 other source(s) (+69%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | finishing | 1/4" | 275 | 0.0021 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | slotting | 3/8" | 275 | 0.0021 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | roughing | 3/8" | 275 | 0.0036 | – ⚠ Outlier (for review): IPT 0.0036 vs median 0.00135 of 6 other source(s) (+167%); SFM 275 vs median 162.5 of 6 other source(s) (+69%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | finishing | 3/8" | 275 | 0.0024 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | slotting | 1/2" | 275 | 0.0027 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | roughing | 1/2" | 275 | 0.0047 | – ⚠ Outlier (for review): IPT 0.0047 vs median 0.001575 of 6 other source(s) (+198%); SFM 275 vs median 162.5 of 6 other source(s) (+69%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | finishing | 1/2" | 275 | 0.0028 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | slotting | 3/4" | 275 | 0.0039 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | roughing | 3/4" | 275 | 0.0068 | – ⚠ Outlier (for review): IPT 0.0068 vs median 0.002437 of 6 other source(s) (+179%); SFM 275 vs median 162.5 of 6 other source(s) (+69%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | finishing | 3/4" | 275 | 0.0034 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | slotting | 1" | 275 | 0.0049 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | roughing | 1" | 275 | 0.0087 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (75 - 98 HRB) | finishing | 1" | 275 | 0.0041 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | slotting | 1/16" | 250 | 0.0003 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | roughing | 1/16" | 250 | 0.0005 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | finishing | 1/16" | 250 | 0.0007 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | slotting | 3/32" | 250 | 0.0004 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | roughing | 3/32" | 250 | 0.0007 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | finishing | 3/32" | 250 | 0.0011 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | slotting | 1/8" | 250 | 0.0005 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | roughing | 1/8" | 250 | 0.0009 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | finishing | 1/8" | 250 | 0.0014 | – ⚠ Outlier (for review): IPT 0.0014 vs median 0.0005 of 4 other source(s) (+180%); SFM 250 vs median 162.5 of 6 other source(s) (+54%) | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | slotting | 3/16" | 250 | 0.0008 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | roughing | 3/16" | 250 | 0.0014 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | finishing | 3/16" | 250 | 0.0016 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | slotting | 1/4" | 250 | 0.001 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | roughing | 1/4" | 250 | 0.0018 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | finishing | 1/4" | 250 | 0.0018 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | slotting | 3/8" | 250 | 0.0015 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | roughing | 3/8" | 250 | 0.0027 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | finishing | 3/8" | 250 | 0.0021 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | slotting | 1/2" | 250 | 0.002 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | roughing | 1/2" | 250 | 0.0036 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | finishing | 1/2" | 250 | 0.0025 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | slotting | 3/4" | 250 | 0.0029 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | roughing | 3/4" | 250 | 0.0051 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | finishing | 3/4" | 250 | 0.0029 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | slotting | 1" | 250 | 0.0037 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | roughing | 1" | 250 | 0.0065 | – ✓ Cross-checked | Helical Solutions |
| Pure titanium: Ti Grade 1, 2, 3, 4, 7, 12 (21 - 36 HRC) | finishing | 1" | 250 | 0.0036 | – ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | slotting | 1/16" | 180 | 0.0002 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | roughing | 1/16" | 180 | 0.0004 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | finishing | 1/16" | 180 | 0.0007 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | slotting | 3/32" | 180 | 0.0003 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | roughing | 3/32" | 180 | 0.0005 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | finishing | 3/32" | 180 | 0.001 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | slotting | 1/8" | 180 | 0.0004 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | roughing | 1/8" | 180 | 0.0007 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | finishing | 1/8" | 180 | 0.0013 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ⚠ Outlier (for review): IPT 0.0013 vs median 0.0005 of 4 other source(s) (+160%); SFM 180 vs median 162.5 of 6 other source(s) (+11%) | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | slotting | 3/16" | 180 | 0.0006 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | roughing | 3/16" | 180 | 0.0011 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | finishing | 3/16" | 180 | 0.0014 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | slotting | 1/4" | 180 | 0.0008 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | roughing | 1/4" | 180 | 0.0014 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | finishing | 1/4" | 180 | 0.0016 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | slotting | 3/8" | 180 | 0.0012 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | roughing | 3/8" | 180 | 0.0021 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | finishing | 3/8" | 180 | 0.0019 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | slotting | 1/2" | 180 | 0.0016 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | roughing | 1/2" | 180 | 0.0028 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | finishing | 1/2" | 180 | 0.0022 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | slotting | 3/4" | 180 | 0.0023 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | roughing | 3/4" | 180 | 0.004 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | finishing | 3/4" | 180 | 0.0026 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | slotting | 1" | 180 | 0.0029 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | roughing | 1" | 180 | 0.0051 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (21 - 36 HRC) | finishing | 1" | 180 | 0.0031 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | slotting | 1/16" | 160 | 0.0002 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | roughing | 1/16" | 160 | 0.0004 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | finishing | 1/16" | 160 | 0.0006 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | slotting | 3/32" | 160 | 0.0003 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | roughing | 3/32" | 160 | 0.0005 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | finishing | 3/32" | 160 | 0.0009 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | slotting | 1/8" | 160 | 0.0004 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | roughing | 1/8" | 160 | 0.0007 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | finishing | 1/8" | 160 | 0.0012 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | slotting | 3/16" | 160 | 0.0006 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | roughing | 3/16" | 160 | 0.001 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | finishing | 3/16" | 160 | 0.0014 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | slotting | 1/4" | 160 | 0.0007 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | roughing | 1/4" | 160 | 0.0013 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | finishing | 1/4" | 160 | 0.0016 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | slotting | 3/8" | 160 | 0.0011 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | roughing | 3/8" | 160 | 0.002 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | finishing | 3/8" | 160 | 0.0018 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | slotting | 1/2" | 160 | 0.0015 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | roughing | 1/2" | 160 | 0.0026 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | finishing | 1/2" | 160 | 0.0021 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | slotting | 3/4" | 160 | 0.0021 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | roughing | 3/4" | 160 | 0.0037 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | finishing | 3/4" | 160 | 0.0025 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | slotting | 1" | 160 | 0.0026 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | roughing | 1" | 160 | 0.0047 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
| Titanium alloy: Ti 3Al-2.5V, Ti 6Al-4V, Ti 10V-2Fe-3Al (36 - 50 HRC) | finishing | 1" | 160 | 0.003 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Helical Solutions |
Lakeshore Carbide: General Purpose End Mill Technical Data / Speeds & Feeds
Tool: General purpose solid carbide end mill (stub/regular/corner radius column). Facts copied with attribution and link; PDF not re-hosted. Lakeshore: "approximate numbers are a good starting point."
| Grade (as listed) | Cut | Dia | SFM | IPT (in) | Review | Source |
|---|---|---|---|---|---|---|
| Titanium, soft | general | 1/32–1/8" | 100–250 | 0.0005–0.0009 | – ✓ Cross-checked | Lakeshore Carbide |
| Titanium, soft | general | 1/8–1/4" | 100–250 | 0.0005–0.001 | – ✓ Cross-checked | Lakeshore Carbide |
| Titanium, soft | general | 1/4–3/8" | 100–250 | 0.0008–0.0015 | – ✓ Cross-checked | Lakeshore Carbide |
| Titanium, soft | general | 3/8–1/2" | 100–250 | 0.001–0.002 | – ✓ Cross-checked | Lakeshore Carbide |
| Titanium, soft | general | 1/2–3/4" | 100–250 | 0.0015–0.004 | – ✓ Cross-checked | Lakeshore Carbide |
| Titanium, soft | general | 3/4–1" | 100–250 | 0.0025–0.0055 | – ✓ Cross-checked | Lakeshore Carbide |
| Titanium, hard | general | 1/32–1/8" | 80–220 | 0.0003–0.0008 | – ✓ Cross-checked | Lakeshore Carbide |
| Titanium, hard | general | 1/8–1/4" | 80–220 | 0.0004–0.0009 | – ✓ Cross-checked | Lakeshore Carbide |
| Titanium, hard | general | 1/4–3/8" | 80–220 | 0.0006–0.0013 | – ✓ Cross-checked | Lakeshore Carbide |
| Titanium, hard | general | 3/8–1/2" | 80–220 | 0.0008–0.0017 | – ✓ Cross-checked | Lakeshore Carbide |
| Titanium, hard | general | 1/2–3/4" | 80–220 | 0.0012–0.0032 | – ✓ Cross-checked | Lakeshore Carbide |
| Titanium, hard | general | 3/4–1" | 80–220 | 0.0015–0.004 | – ✓ Cross-checked | Lakeshore Carbide |
OSG: Standard 2 Flute HSS-Co end mills: tech page (slotting)
Tool: 2-flute HSS-Co (cobalt high-speed steel) end mill, uncoated (OSG notes TiN/TiCN versions allow up to 15-20% more speed). Facts copied with attribution and link; PDF not re-hosted.
| Grade (as listed) | Cut | Dia | SFM | IPT (in) | Review | Source |
|---|---|---|---|---|---|---|
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 1/64" | 50–65 | 1e-05 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 1/32" | 50–65 | 5e-05 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 3/64" | 50–65 | 0.0001 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 1/16" | 50–65 | 0.00014 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 5/64" | 50–65 | 0.0002 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 3/32" | 50–65 | 0.00028 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 7/64" | 50–65 | 0.00033 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 1/8" | 50–65 | 0.0004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 9/64" | 50–65 | 0.00047 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 5/32" | 50–65 | 0.00056 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 11/64" | 50–65 | 0.00067 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 3/16" | 50–65 | 0.0008 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 1/4" | 50–65 | 0.00112 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 5/16" | 50–65 | 0.0016 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 3/8" | 50–65 | 0.0019 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 7/16" | 50–65 | 0.0025 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 1/2" | 50–65 | 0.00265 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 9/16" | 50–65 | 0.003 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 5/8" | 50–65 | 0.00335 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 11/16" | 50–65 | 0.00355 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 3/4" | 50–65 | 0.00355 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 13/16" | 50–65 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 7/8" | 50–65 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 15/16" | 50–65 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 1" | 50–65 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 1 1/8" | 50–65 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 1 1/4" | 50–65 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 1 3/8" | 50–65 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 1 1/2" | 50–65 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 1 5/8" | 50–65 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 1 3/4" | 50–65 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 1 7/8" | 50–65 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | slotting | 2" | 50–65 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 1/64" | 80–150 | 2e-05 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 1/64" | 16–32 | 1e-05 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 1/32" | 80–150 | 4e-05 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 1/32" | 16–32 | 3e-05 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 3/64" | 80–150 | 9e-05 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 3/64" | 16–32 | 6e-05 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 1/16" | 80–150 | 0.00012 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.00012 vs median 0.00012 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 1/16" | 16–32 | 8e-05 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 5/64" | 80–150 | 0.00017 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.00017 vs median 0.00017 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 5/64" | 16–32 | 0.00011 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 3/32" | 80–150 | 0.00024 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.00024 vs median 0.00024 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 3/32" | 16–32 | 0.00016 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 7/64" | 80–150 | 0.00028 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.00028 vs median 0.00028 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 7/64" | 16–32 | 0.0002 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 1/8" | 80–150 | 0.00034 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.00034 vs median 0.00034 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 1/8" | 16–32 | 0.00024 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 9/64" | 80–150 | 0.0004 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.0004 vs median 0.0004 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 9/64" | 16–32 | 0.00028 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 5/32" | 80–150 | 0.00048 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.00048 vs median 0.00048 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 5/32" | 16–32 | 0.00034 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 11/64" | 80–150 | 0.00056 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.00056 vs median 0.00056 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 11/64" | 16–32 | 0.0004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 3/16" | 80–150 | 0.00067 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.00067 vs median 0.00067 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 3/16" | 16–32 | 0.00048 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 1/4" | 80–150 | 0.00095 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.00095 vs median 0.00095 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 1/4" | 16–32 | 0.00071 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 5/16" | 80–150 | 0.00132 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.00132 vs median 0.00132 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 5/16" | 16–32 | 0.001 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 3/8" | 80–150 | 0.0016 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.0016 vs median 0.0016 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 3/8" | 16–32 | 0.00118 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 7/16" | 80–150 | 0.00212 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.00212 vs median 0.00212 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 7/16" | 16–32 | 0.0014 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 1/2" | 80–150 | 0.00236 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.00236 vs median 0.00236 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 1/2" | 16–32 | 0.0018 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 9/16" | 80–150 | 0.0028 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.0028 vs median 0.0028 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 9/16" | 16–32 | 0.002 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 5/8" | 80–150 | 0.00315 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.00315 vs median 0.00315 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 5/8" | 16–32 | 0.00224 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 11/16" | 80–150 | 0.00355 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.00355 vs median 0.00355 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 11/16" | 16–32 | 0.0025 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 3/4" | 80–150 | 0.00355 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.00355 vs median 0.00355 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 3/4" | 16–32 | 0.0025 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 13/16" | 80–150 | 0.004 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.004 vs median 0.004 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 13/16" | 16–32 | 0.0028 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 7/8" | 80–150 | 0.004 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.004 vs median 0.004 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 7/8" | 16–32 | 0.00315 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 15/16" | 80–150 | 0.004 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.004 vs median 0.004 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 15/16" | 16–32 | 0.00355 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 1" | 80–150 | 0.004 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.004 vs median 0.004 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 1" | 16–32 | 0.00355 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 1 1/8" | 80–150 | 0.004 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.004 vs median 0.004 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 1 1/8" | 16–32 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 1 1/4" | 80–150 | 0.004 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.004 vs median 0.004 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 1 1/4" | 16–32 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 1 3/8" | 80–150 | 0.004 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.004 vs median 0.004 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 1 3/8" | 16–32 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 1 1/2" | 80–150 | 0.004 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.004 vs median 0.004 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 1 1/2" | 16–32 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 1 5/8" | 80–150 | 0.004 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 1 5/8" | 16–32 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 1 3/4" | 80–150 | 0.004 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.004 vs median 0.004 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 1 3/4" | 16–32 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 1 7/8" | 80–150 | 0.004 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 1 7/8" | 16–32 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | slotting | 2" | 80–150 | 0.004 | ⚠ OSG prints 80-150 SFM for this 30-40 HRC column (same as mild steel); verify against the PDF before relying on it. Slotting, axial depth 0.5×D (as printed). ⚠ Outlier (for review): IPT 0.004 vs median 0.004 of 1 other source(s) (+0%); SFM 115 vs median 24 of 1 other source(s) (+379%) | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | slotting | 2" | 16–32 | 0.004 | Slotting, axial depth 0.5×D (as printed). ✓ Cross-checked | OSG |
OSG: Standard 4 Flute and 6 Flute HSS-Co end mills: tech page (side milling)
Tool: 4-flute HSS-Co (cobalt high-speed steel) end mill. Facts copied with attribution and link; PDF not re-hosted.
| Grade (as listed) | Cut | Dia | SFM | IPT (in) | Review | Source |
|---|---|---|---|---|---|---|
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 1/16" | 16–32 | 0.00014 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 5/64" | 16–32 | 0.0002 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 3/32" | 16–32 | 0.00028 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 7/64" | 16–32 | 0.00034 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 1/8" | 16–32 | 0.0004 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 9/64" | 16–32 | 0.00048 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 5/32" | 16–32 | 0.00056 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 11/64" | 16–32 | 0.00067 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 3/16" | 16–32 | 0.0008 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 1/4" | 16–32 | 0.00112 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 5/16" | 16–32 | 0.0016 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 3/8" | 16–32 | 0.0019 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 7/16" | 16–32 | 0.0025 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 1/2" | 16–32 | 0.00265 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 9/16" | 16–32 | 0.003 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 5/8" | 16–32 | 0.00335 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 11/16" | 16–32 | 0.00355 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 3/4" | 16–32 | 0.00355 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 13/16" | 16–32 | 0.004 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 7/8" | 16–32 | 0.004 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 15/16" | 16–32 | 0.004 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 1" | 16–32 | 0.004 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 1 1/8" | 16–32 | 0.004 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 1 1/4" | 16–32 | 0.004 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 1 3/8" | 16–32 | 0.004 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 1 1/2" | 16–32 | 0.004 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 1 3/4" | 16–32 | 0.004 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Unalloyed titanium / high tensile steels (20-30 HRC) | profiling (side milling) | 2" | 16–32 | 0.004 | ⚠ OSG prints 16-32 SFM here vs 50-65 SFM on its 2-flute page for the same column; verify. Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 1/16" | 30–50 | 0.00012 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 1/16" | 16–32 | 8e-05 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 5/64" | 30–50 | 0.00017 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 5/64" | 16–32 | 0.00011 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 3/32" | 30–50 | 0.00024 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 3/32" | 16–32 | 0.00016 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 7/64" | 30–50 | 0.00028 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 7/64" | 16–32 | 0.0002 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 1/8" | 30–50 | 0.00034 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 1/8" | 16–32 | 0.00024 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 9/64" | 30–50 | 0.0004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 9/64" | 16–32 | 0.00028 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 5/32" | 30–50 | 0.00048 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 5/32" | 16–32 | 0.00034 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 11/64" | 30–50 | 0.00056 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 11/64" | 16–32 | 0.0004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 3/16" | 30–50 | 0.00067 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 3/16" | 16–32 | 0.00048 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 1/4" | 30–50 | 0.00095 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 1/4" | 16–32 | 0.00071 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 5/16" | 30–50 | 0.00132 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 5/16" | 16–32 | 0.001 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 3/8" | 30–50 | 0.0016 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 3/8" | 16–32 | 0.00118 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 7/16" | 30–50 | 0.00212 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 7/16" | 16–32 | 0.0014 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 1/2" | 30–50 | 0.00236 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 1/2" | 16–32 | 0.0018 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 9/16" | 30–50 | 0.0028 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 9/16" | 16–32 | 0.002 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 5/8" | 30–50 | 0.00315 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 5/8" | 16–32 | 0.00224 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 11/16" | 30–50 | 0.00355 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 11/16" | 16–32 | 0.0025 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 3/4" | 30–50 | 0.00355 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 3/4" | 16–32 | 0.0025 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 13/16" | 30–50 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 13/16" | 16–32 | 0.0028 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 7/8" | 30–50 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 7/8" | 16–32 | 0.00315 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 15/16" | 30–50 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 15/16" | 16–32 | 0.00355 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 1" | 30–50 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 1" | 16–32 | 0.00355 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 1 1/8" | 30–50 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 1 1/8" | 16–32 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 1 1/4" | 30–50 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 1 1/4" | 16–32 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 1 3/8" | 30–50 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 1 3/8" | 16–32 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 1 1/2" | 30–50 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 1 1/2" | 16–32 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 1 3/4" | 30–50 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 1 3/4" | 16–32 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| Medium strength stainless steels and titanium alloys (30-40 HRC) | profiling (side milling) | 2" | 30–50 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
| High strength stainless steels and titanium alloys (40-50 HRC) | profiling (side milling) | 2" | 16–32 | 0.004 | Side milling, axial 1.5×D, radial 0.1×D (as printed). ✓ Cross-checked | OSG |
Accupro (MSC Industrial): General Purpose End Mills Recommended Speed and Feed (under and over 32 HRC)
Tool: General purpose carbide end mill, coated (Accupro: reduce rates up to 50% for uncoated). Facts copied with attribution and link; PDF not re-hosted.
| Grade (as listed) | Cut | Dia | SFM | IPT (in) | Review | Source |
|---|---|---|---|---|---|---|
| Titanium alloys: 6Al-4V, ASTM 1/2/3 (<32 HRC) | general | 1/8" | 150–250 | 0.0005 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Accupro |
| Titanium alloys: 6Al-4V, ASTM 1/2/3 (<32 HRC) | general | 3/16" | 150–250 | 0.00075 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Accupro |
| Titanium alloys: 6Al-4V, ASTM 1/2/3 (<32 HRC) | general | 1/4" | 150–250 | 0.0011 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Accupro |
| Titanium alloys: 6Al-4V, ASTM 1/2/3 (<32 HRC) | general | 3/8" | 150–250 | 0.0018 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Accupro |
| Titanium alloys: 6Al-4V, ASTM 1/2/3 (<32 HRC) | general | 1/2" | 150–250 | 0.0025 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Accupro |
| Titanium alloys: 6Al-4V, ASTM 1/2/3 (<32 HRC) | general | 5/8" | 150–250 | 0.0031 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Accupro |
| Titanium alloys: 6Al-4V, ASTM 1/2/3 (<32 HRC) | general | 3/4" | 150–250 | 0.0037 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Accupro |
| Titanium alloys: 6Al-4V, ASTM 1/2/3 (<32 HRC) | general | 1" | 150–250 | 0.005 | Spot-checked 2026-10-16: Ti 6Al-4V: typical carbide start ~150–200 SFM per Accupro/Harvey. ✓ Cross-checked | Accupro |
| Titanium alloys: 5Al-2.5Sn-ELI, 8Al-1Mo-1V (>32 HRC) | general | 1/8" | 90–160 | 0.0005 | – ✓ Cross-checked | Accupro |
| Titanium alloys: 5Al-2.5Sn-ELI, 8Al-1Mo-1V (>32 HRC) | general | 3/16" | 90–160 | 0.00075 | – ✓ Cross-checked | Accupro |
| Titanium alloys: 5Al-2.5Sn-ELI, 8Al-1Mo-1V (>32 HRC) | general | 1/4" | 90–160 | 0.0011 | – ✓ Cross-checked | Accupro |
| Titanium alloys: 5Al-2.5Sn-ELI, 8Al-1Mo-1V (>32 HRC) | general | 3/8" | 90–160 | 0.0018 | – ✓ Cross-checked | Accupro |
| Titanium alloys: 5Al-2.5Sn-ELI, 8Al-1Mo-1V (>32 HRC) | general | 1/2" | 90–160 | 0.0025 | – ✓ Cross-checked | Accupro |
| Titanium alloys: 5Al-2.5Sn-ELI, 8Al-1Mo-1V (>32 HRC) | general | 5/8" | 90–160 | 0.0031 | – ✓ Cross-checked | Accupro |
| Titanium alloys: 5Al-2.5Sn-ELI, 8Al-1Mo-1V (>32 HRC) | general | 3/4" | 90–160 | 0.0037 | – ✓ Cross-checked | Accupro |
| Titanium alloys: 5Al-2.5Sn-ELI, 8Al-1Mo-1V (>32 HRC) | general | 1" | 90–160 | 0.005 | – ✓ Cross-checked | Accupro |
Lakeshore Carbide: Carbide Roughers (variable helix): starting speeds and feeds
Tool: Variable-helix carbide rougher (3 flutes at 3/16", 4 flutes 1/4" and up). Facts copied with attribution and link; PDF not re-hosted.
| Grade (as listed) | Cut | Dia | SFM | IPT (in) | Review | Source |
|---|---|---|---|---|---|---|
| Titanium | roughing | 3/16" | 125–215 | 0.0007–0.0013 | ⚠ SFM header is printed slightly out of line with the columns in the PDF; check the column order before relying on titanium/stainless SFM. Strong coolant blast recommended (as printed). ✓ Cross-checked | Lakeshore Carbide |
| Titanium | roughing | 1/4" | 125–215 | 0.0007–0.0013 | ⚠ SFM header is printed slightly out of line with the columns in the PDF; check the column order before relying on titanium/stainless SFM. Strong coolant blast recommended (as printed). ✓ Cross-checked | Lakeshore Carbide |
| Titanium | roughing | 5/16" | 125–215 | 0.0009–0.0015 | ⚠ SFM header is printed slightly out of line with the columns in the PDF; check the column order before relying on titanium/stainless SFM. Strong coolant blast recommended (as printed). ✓ Cross-checked | Lakeshore Carbide |
| Titanium | roughing | 3/8" | 125–215 | 0.0009–0.0015 | ⚠ SFM header is printed slightly out of line with the columns in the PDF; check the column order before relying on titanium/stainless SFM. Strong coolant blast recommended (as printed). ✓ Cross-checked | Lakeshore Carbide |
| Titanium | roughing | 1/2" | 125–215 | 0.001–0.0018 | ⚠ SFM header is printed slightly out of line with the columns in the PDF; check the column order before relying on titanium/stainless SFM. Strong coolant blast recommended (as printed). ✓ Cross-checked | Lakeshore Carbide |
| Titanium | roughing | 5/8" | 125–215 | 0.0012–0.0022 | ⚠ SFM header is printed slightly out of line with the columns in the PDF; check the column order before relying on titanium/stainless SFM. Strong coolant blast recommended (as printed). ✓ Cross-checked | Lakeshore Carbide |
| Titanium | roughing | 3/4" | 125–215 | 0.0015–0.0025 | ⚠ SFM header is printed slightly out of line with the columns in the PDF; check the column order before relying on titanium/stainless SFM. Strong coolant blast recommended (as printed). ✓ Cross-checked | Lakeshore Carbide |
| Titanium | roughing | 1" | 125–215 | 0.0018–0.0027 | ⚠ SFM header is printed slightly out of line with the columns in the PDF; check the column order before relying on titanium/stainless SFM. Strong coolant blast recommended (as printed). ✓ Cross-checked | Lakeshore Carbide |
Lakeshore Carbide: Six Flute high-performance profiling mill (AlTiN coated)
Tool: 6-flute AlTiN-coated carbide profiling end mill. Facts copied with attribution and link; PDF not re-hosted.
| Grade (as listed) | Cut | Dia | SFM | IPT (in) | Review | Source |
|---|---|---|---|---|---|---|
| Titanium and alloys | profiling (side milling) | 1/4" | 250–400 | 0.001–0.002 | Use 5-30% radial depth of cut (Lakeshore tech note). ✓ Cross-checked | Lakeshore Carbide |
| Titanium and alloys | profiling (side milling) | 3/8" | 250–400 | 0.001–0.002 | Use 5-30% radial depth of cut (Lakeshore tech note). ✓ Cross-checked | Lakeshore Carbide |
| Titanium and alloys | profiling (side milling) | 1/2" | 250–400 | 0.001–0.0025 | Use 5-30% radial depth of cut (Lakeshore tech note). ✓ Cross-checked | Lakeshore Carbide |
| Titanium and alloys | profiling (side milling) | 5/8" | 250–400 | 0.002–0.003 | Use 5-30% radial depth of cut (Lakeshore tech note). ✓ Cross-checked | Lakeshore Carbide |
| Titanium and alloys | profiling (side milling) | 3/4" | 250–400 | 0.0025–0.004 | Use 5-30% radial depth of cut (Lakeshore tech note). ✓ Cross-checked | Lakeshore Carbide |
| Titanium and alloys | profiling (side milling) | 1" | 250–400 | 0.004–0.006 | Use 5-30% radial depth of cut (Lakeshore tech note). ✓ Cross-checked | Lakeshore Carbide |
SGS / Kyocera SGS Precision Tools: Series Z5, Z5CR fractional speed & feed recommendations
Tool: Z-Carb Z5: 5-flute variable-helix carbide end mill (coated). Facts copied with attribution and link; PDF not re-hosted.
| Grade (as listed) | Cut | Dia | SFM | IPT (in) | Review | Source |
|---|---|---|---|---|---|---|
| Titanium alloys: pure Ti, Ti6Al4V, Ti6Al2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si (≤350 HB) | profiling (side milling) | 1/8" | 172–258 | 0.0003 | Profile: Ae ≤0.5×D, Ap ≤1.5×D. SGS nominal 215 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Titanium alloys: pure Ti, Ti6Al4V, Ti6Al2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si (≤350 HB) | profiling (side milling) | 1/4" | 172–258 | 0.0008 | Profile: Ae ≤0.5×D, Ap ≤1.5×D. SGS nominal 215 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Titanium alloys: pure Ti, Ti6Al4V, Ti6Al2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si (≤350 HB) | profiling (side milling) | 3/8" | 172–258 | 0.0015 | Profile: Ae ≤0.5×D, Ap ≤1.5×D. SGS nominal 215 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Titanium alloys: pure Ti, Ti6Al4V, Ti6Al2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si (≤350 HB) | profiling (side milling) | 1/2" | 172–258 | 0.002 | Profile: Ae ≤0.5×D, Ap ≤1.5×D. SGS nominal 215 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Titanium alloys: pure Ti, Ti6Al4V, Ti6Al2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si (≤350 HB) | profiling (side milling) | 5/8" | 172–258 | 0.0022 | Profile: Ae ≤0.5×D, Ap ≤1.5×D. SGS nominal 215 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Titanium alloys: pure Ti, Ti6Al4V, Ti6Al2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si (≤350 HB) | profiling (side milling) | 3/4" | 172–258 | 0.0024 | Profile: Ae ≤0.5×D, Ap ≤1.5×D. SGS nominal 215 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Titanium alloys: pure Ti, Ti6Al4V, Ti6Al2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si (≤350 HB) | profiling (side milling) | 1" | 172–258 | 0.0028 | Profile: Ae ≤0.5×D, Ap ≤1.5×D. SGS nominal 215 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Titanium alloys: pure Ti, Ti6Al4V, Ti6Al2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si (≤350 HB) | slotting | 1/8" | 136–204 | 0.0003 | Slot: Ae 1×D, Ap ≤1×D. SGS nominal 170 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Titanium alloys: pure Ti, Ti6Al4V, Ti6Al2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si (≤350 HB) | slotting | 1/4" | 136–204 | 0.0008 | Slot: Ae 1×D, Ap ≤1×D. SGS nominal 170 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Titanium alloys: pure Ti, Ti6Al4V, Ti6Al2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si (≤350 HB) | slotting | 3/8" | 136–204 | 0.0015 | Slot: Ae 1×D, Ap ≤1×D. SGS nominal 170 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Titanium alloys: pure Ti, Ti6Al4V, Ti6Al2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si (≤350 HB) | slotting | 1/2" | 136–204 | 0.002 | Slot: Ae 1×D, Ap ≤1×D. SGS nominal 170 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Titanium alloys: pure Ti, Ti6Al4V, Ti6Al2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si (≤350 HB) | slotting | 5/8" | 136–204 | 0.0022 | Slot: Ae 1×D, Ap ≤1×D. SGS nominal 170 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Titanium alloys: pure Ti, Ti6Al4V, Ti6Al2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si (≤350 HB) | slotting | 3/4" | 136–204 | 0.0024 | Slot: Ae 1×D, Ap ≤1×D. SGS nominal 170 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Titanium alloys: pure Ti, Ti6Al4V, Ti6Al2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si (≤350 HB) | slotting | 1" | 136–204 | 0.0028 | Slot: Ae 1×D, Ap ≤1×D. SGS nominal 170 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Difficult titanium alloys: Ti10V2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo and others (>350, ≤440 HB) | profiling (side milling) | 1/8" | 60–90 | 0.0003 | Profile: Ae ≤0.5×D, Ap ≤1.5×D. SGS nominal 75 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Difficult titanium alloys: Ti10V2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo and others (>350, ≤440 HB) | profiling (side milling) | 1/4" | 60–90 | 0.0008 | Profile: Ae ≤0.5×D, Ap ≤1.5×D. SGS nominal 75 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Difficult titanium alloys: Ti10V2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo and others (>350, ≤440 HB) | profiling (side milling) | 3/8" | 60–90 | 0.0015 | Profile: Ae ≤0.5×D, Ap ≤1.5×D. SGS nominal 75 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Difficult titanium alloys: Ti10V2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo and others (>350, ≤440 HB) | profiling (side milling) | 1/2" | 60–90 | 0.002 | Profile: Ae ≤0.5×D, Ap ≤1.5×D. SGS nominal 75 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Difficult titanium alloys: Ti10V2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo and others (>350, ≤440 HB) | profiling (side milling) | 5/8" | 60–90 | 0.0022 | Profile: Ae ≤0.5×D, Ap ≤1.5×D. SGS nominal 75 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Difficult titanium alloys: Ti10V2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo and others (>350, ≤440 HB) | profiling (side milling) | 3/4" | 60–90 | 0.0024 | Profile: Ae ≤0.5×D, Ap ≤1.5×D. SGS nominal 75 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Difficult titanium alloys: Ti10V2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo and others (>350, ≤440 HB) | profiling (side milling) | 1" | 60–90 | 0.0028 | Profile: Ae ≤0.5×D, Ap ≤1.5×D. SGS nominal 75 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ✓ Cross-checked | SGS / Kyocera SGS Precision Tools |
| Difficult titanium alloys: Ti10V2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo and others (>350, ≤440 HB) | slotting | 1/8" | 48–72 | 0.0003 | Slot: Ae 1×D, Ap ≤1×D. SGS nominal 60 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ⚠ Outlier (for review): IPT 0.0003 vs median 0.0005625 of 4 other source(s) (-47%); SFM 60 vs median 166.2 of 6 other source(s) (-64%) | SGS / Kyocera SGS Precision Tools |
| Difficult titanium alloys: Ti10V2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo and others (>350, ≤440 HB) | slotting | 1/4" | 48–72 | 0.0008 | Slot: Ae 1×D, Ap ≤1×D. SGS nominal 60 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ⚠ Outlier (for review): IPT 0.0008 vs median 0.00105 of 6 other source(s) (-24%); SFM 60 vs median 166.2 of 6 other source(s) (-64%) | SGS / Kyocera SGS Precision Tools |
| Difficult titanium alloys: Ti10V2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo and others (>350, ≤440 HB) | slotting | 3/8" | 48–72 | 0.0015 | Slot: Ae 1×D, Ap ≤1×D. SGS nominal 60 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ⚠ Outlier (for review): IPT 0.0015 vs median 0.00135 of 6 other source(s) (+11%); SFM 60 vs median 166.2 of 6 other source(s) (-64%) | SGS / Kyocera SGS Precision Tools |
| Difficult titanium alloys: Ti10V2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo and others (>350, ≤440 HB) | slotting | 1/2" | 48–72 | 0.002 | Slot: Ae 1×D, Ap ≤1×D. SGS nominal 60 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ⚠ Outlier (for review): IPT 0.002 vs median 0.001575 of 6 other source(s) (+27%); SFM 60 vs median 166.2 of 6 other source(s) (-64%) | SGS / Kyocera SGS Precision Tools |
| Difficult titanium alloys: Ti10V2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo and others (>350, ≤440 HB) | slotting | 5/8" | 48–72 | 0.0022 | Slot: Ae 1×D, Ap ≤1×D. SGS nominal 60 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ⚠ Outlier (for review): IPT 0.0022 vs median 0.0021 of 4 other source(s) (+5%); SFM 60 vs median 166.2 of 6 other source(s) (-64%) | SGS / Kyocera SGS Precision Tools |
| Difficult titanium alloys: Ti10V2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo and others (>350, ≤440 HB) | slotting | 3/4" | 48–72 | 0.0024 | Slot: Ae 1×D, Ap ≤1×D. SGS nominal 60 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ⚠ Outlier (for review): IPT 0.0024 vs median 0.002863 of 6 other source(s) (-16%); SFM 60 vs median 166.2 of 6 other source(s) (-64%) | SGS / Kyocera SGS Precision Tools |
| Difficult titanium alloys: Ti10V2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo and others (>350, ≤440 HB) | slotting | 1" | 48–72 | 0.0028 | Slot: Ae 1×D, Ap ≤1×D. SGS nominal 60 SFM (range shown). Ramp ≤5°, do not plunge (as printed). ⚠ Outlier (for review): IPT 0.0028 vs median 0.00425 of 6 other source(s) (-34%); SFM 60 vs median 166.2 of 6 other source(s) (-64%) | SGS / Kyocera SGS Precision Tools |
Weekly "what changed" email: coming soon
We'll email you when a maker updates their feeds and speeds.